Header

Down & Dirty, Part 1

 

 

 

In the world of “clean,” particle size is defined in microns, an ideal measurement used for measuring things smaller than the naked eye can see. A micron (µ), short for micrometer, is a metric unit of measurement equal to one millionth of a meter or about 4 hundred thousandths of an inch (0.00004”). To help put this in perspective, the period used to end this sentence is about 397 microns in diameter. The eye of a needle used to stitch a child’s pants would be around 749 microns wide, a human hair 40 to 120 microns in diameter, and a stamp more than 25,000 microns on a side.

Here are some examples of “particles” and their sizes: Grain of table salt, 100 µ; human hair diameter, 70 µ; limit of visibility, 40 µ; white blood cell, 25 µ; red blood cell, 8 µ; bacteria, 2 µ.

Hydraulic filters used on modern heavy equipment are typically designed to remove particles between 7-10 µ. Examples are dirt, metal shavings, seal material, etc.  If we ran human blood through the same filters, they would actually remove the white blood cells!

The International Organization for Standardization (ISO) created the cleanliness code 4406:1999 to quantify particulate contamination levels per milliliter of fluid. This code defines cleanliness in terms of the number of particles per unit volume greater than 4, 6 and 14 µ, respectively. The code is expressed in three numbers; the lower the ISO code rating, the cleaner the oil. For example a rating of 16/14/11 is much cleaner than 17/14/13. Because most of the particles are too small for the naked eye to see, it is difficult to use the ISO Code rating unless it references test results such as oil sample analyses.

Particle Invasion

There are many culprits. Some of the most common avenues of contamination are:
Adding unfiltered oil directly to the hydraulic tank; Operating with high hydraulic oil temperatures (heat causes hoses, seals or other components to degenerate and contaminate oil); Using low viscosity oils. Thin oils have reduced lubrication capability. Thin oil films increase the chances for metal-to-metal contact and resulting metallic shavings/particles entering the oil stream; Normal component wear over time; Replacing components in a dirty environment; Using hoses that have not been properly cleaned after assembly. Using dirty hoses is one of the easiest ways to ensure component failure.

Particles Damage

A multitude of issues on the machine can be attributed to contamination, only a few of which are discussed here. Machines today frequently use piston pumps and motors operating at very high pressures. These precision components are manufactured with very tight tolerances for high performance and efficiency. The tighter these tolerances become, the more susceptible these components are to damage from small debris particles in dirty oil.

Main hydraulic valves are particularly susceptible to damage and poor or erratic operation due to the precise fit between spools and valve housings. Spools can be scored or even bind up by particle contamination. Small orifices, passages and seats can also prevent flow or leak from particle contamination, causing hydraulic malfunction.

The plungers in a piston pump or motor are lubricated through small oil passages in each of the pistons. Lack of lubrication from plugged oil passages can result in catastrophic failure. Catastrophic hydraulic component failures contaminate the system with metal shavings that eventually clog the hydraulic return oil filter. Some return oil filters have a filter bypass that opens when filters plug and backpressure gets too high, dumping unfiltered trouble right back to the tank! Once in the tank, contaminated oil gets circulated through the system to cause more damage. What does this all mean for the machine owner? It means reduced component performance, reduced machine production, increased downtime, shorter component life and higher repair costs.

7 Anti-contamination Tips

1. Use recommended hydraulic oils that meet manufacturer specifications and make sure the ISO grade is appropriate for the ambient temperatures encountered.

2. Never add oil through a tank access cover! Hydraulic oil straight from the drum will contaminate the hydraulic system. All oil must be pre-filtered before entering the reservoir.

3. Keep an eye out for plugged filter indicators. When a filter clogs an indicator light warning of higher than normal filter back pressure indicator should illuminate. When this indicator is tripped, inspect and replace filters as soon as possible. Remember, when oil bypasses the filter element, unfiltered oil is being redirected back to tank.

4. When changing filter elements, inspect the oil around the element for metal flakes before removing it. If flakes are present or if there has been a pump or motor failure recently, do not remove the filter element. Doing so will allow the contaminated oil around the element to drain directly into the tank. Remove the entire filter assembly to change the element, this will help contain debris.

5. Clean hoses thoroughly before installation.

6. Replace all components, including hoses, in the cleanest environment possible. Make sure hoses and ports are capped during transportation and before installation.

7. Test the hydraulic fluid for contamination on a regular basis, especially if only one type of oil is used throughout the year.

Article by Kurt Moncini, Marketing Director, Forest Machine Business Department, Komatsu, America Corporation

Latest News

Sponsored Content Provided By John Deere

Sponsored Content Provided By John Deere

Forestry is a complex business that requires seamless coordination in the woods and the office. John Deere Precision Forestry helps increase the efficiency and productivity of your operation. Focusing on jobsite technology lets you select and adopt solutions based on your unique applications…

What’s Next?

What’s Next?

As I look at my little boys I often think about what’s next for them; how can I set them up for success? Is playing ball their future? Am I doing right by forcing them to eat zoodles? In my personal life, in the daily grind, it is easy to see how fast (and slow) time moves. I know one day I will no longer be my kids’ taxi service and will be ugly crying at their high school graduations. But that’s expected: the natural order of time marching on.

Enviva Establishes Heirs Property Fund

Enviva Establishes Heirs Property Fund

Enviva Inc., the world’s largest producer of industrial wood pellets, has announced the establishment of the Enviva Heirs Property Fund (EHPF), an initiative dedicated to ending involuntary land loss across the U.S. Southeast. Enviva has formally…

Have A Question?

Send Us A Message